Suppliers of steel products.

steel c1010 yield

Leave a comment

301 Stainless Steel 1/2 Hard Cold Rolled Strip & Coils

301 Stainless Steel 1/2 Hard This Type 301 half hard Stainless Strip has been produced to meet a need for an in-between forming Quality Strip within a hardness range calling for minimum tensile and yield strengths at 150,000 PSI and 110,000 PSI with elongation in 2 inches at 15-18%. 301 Stainless Steel 1/2 Hard Cold Rolled Strip & Coils 301 Stainless Steel 1/2 Hard This Type 301 half hard Stainless Strip has been produced to meet a need for an in-between forming Quality Strip within a hardness range calling for minimum tensile and yield strengths at 150,000 PSI and 110,000 PSI with elongation in 2 inches at 15-18%.

AISI 1018 Carbon Steel - 1018 Steel Properties All

C1018 is a general purpose carbon steel that is easily machined and welded and may be hardened by carburizing and by other surface-hardening methods. C1018 is forged from around 2300ºF down to a temperature in the region of 1650ºF (1260ºC down to 900ºC.). All Metals & Forge Group is an ISO 9001:2008, AS/EN9100:2009 Rev. C manufacturer AISI 1022 Low Carbon Steel - AZoMAISI 1022 steel requires 482.2°C -93.3 °C (900°F to 200°F) for the hot working process. Forging. AISI 1022 steel is forged at 1288 °C-982°C (2350°F to 1800°F). The steel is heated to a maximum of 1100°C to 1200°C, held till the temperature is uniform throughout the section and forging is commenced. ASTM 1010 Steel Chemical composition, Metal Properties Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. ASTM 1010 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86-80247006 E-mail:[email protected]

ASTM SAE AISI 1018 Carbon Steel Chemical Composition

AISI SAE ASTM 1018 steel has many semifinished and final products such as round bar, flat bar, steel tubing and pipes, etc. 1018 carbon steel is versatile and is commonly used in a variety of carburized parts such as gears, pinions, ratchets, worms, pins, chain C1010 - Brown Metals CompanyC1010, sometimes referred to as C1008, is a common or ordinary low carbon (0.25% maximum) steel as contrasted with special or alloy steels, which contain other alloying metals in addition to the usual constituents of steel in their common percentages. Cold Rolled 1008/1010 Steel Physical & Chemical PropertiesCold Rolled 1008/1010 Steel Physical Properties; ASTM A1008/1010:Temper Designation Alloy; Dead Soft:DS Type - B:1008:Commercial Quality:CS Type - B:1008/1010

DOM Tubing A513 Type 5 - Drawn Over Mandrel - TW

TW stocks a full range of DOM carbon tubing sizes. Our DOM (Drawn Over Mandrel) tubing is produced in carbon grades 1020-1026 to the ASTM A513 Type 5 specification. In addition, we can special-order a wide variety of non-standard sizes of dom tubing. DOM TUBING APPLICATIONS: Data Sheet:CRS 1010Cold Rolled Steel (CRS) SAE type 1010 is a low alloyed steel that is drawn /rolled cold for obtaining superior surface finish and increased hardness. It is usually produced in bar/rod form and rolled/extruded in it final form. Depending further processing, CRS1010 is available in Datasheet for Steel Grades Carbon Steel AISI 1010Steel GradesAISI 1010 Chemical information,Mechanical properties Physical properties, Mechanical properties, Heat treatment, and Micro structure AISI 1010 Physical Properties Tensile strength 115-234 b/MPa Yield Strength 23 0.2 /MPa Elongation 65 5 (%) - (%) Akv - Akv/J HBS 123-321 - HRC 30 - AISI 1010 Mechanical Properties

ERW Standard and Line Pipe Grades - Continental Steel

Grade A Carbon Steel (ASTM A53, A523, API 5L PSL1 ) Minimum Yield Strength:30,000 psi Maximum Yield Strength:None Minimum Tensile Strength:48,000 psi Notes:This grade may be used for standard pipe, line pipe, or conduit pipeas specified in the various ASTM and API specifications. Grade B Carbon Steel (ASTM A53, A523, API [] Hardness Conversion Table for Carbon and Alloy SteelsHardness Testing Hardness testing can best be described as a measurement of resistance to penetration to a defined load. Several types or methods of hardness testing are more common and found in this table. See More Brinell Testing is a fairly simple test but the most destructive type. It SAE AISI 1020 Steel Properties, C1020 Carbon Steel Yield The following data shows that AISI SAE 1020 steel mechanical properties include yield strength, tensile strength, elongation, section reduction, and hardness in various conditions. SAE AISI 1020 steel Youngs modulus (modulus of elasticity) in the as-received condition:186 GPa (27×10 6 psi).

Technical Information for C1010 - Stainless Steel Strip

C1010, sometimes referred to as C1008, is a common or ordinary low carbon (0.25% maximum) steel as contrasted with special or alloy steels, which contain other alloying metals in addition to the usual constituents of steel in their common percentages. eFunda:Properties of Carbon Steel AISI 1010Category :Steel:Class :Carbon steel:Type :Standard:Designations :France:AFNOR XC 10 Germany:DIN 1.1121 Japan:JIS S12C , JIS S1OC , JIS S9CK United States eFunda:Properties of Carbon Steel AISI 1010Category :Steel:Class :Carbon steel:Type :Standard:Designations :France:AFNOR XC 10 Germany:DIN 1.1121 Japan:JIS S12C , JIS S1OC , JIS S9CK United States

hot-roll-steel A513 Product Guide from Online Metals

A513 steel is a high-carbon alloy that offers a uniform grain structure which gives it a strong, seamless and consistent structure. The high carbon content increases strength and rigidity while slightly lowering machinability and weldability. Cold Rolled Steel C1010 Metal Supermarkets - Steel Grade Summary:Cold Rolled C1010 Steel is produced from rimmed, capped and semi-killed steel and are intended for exposed or unexposed parts involving bending, moderate drawing or forming and welding. This material should be painted or plated to prevent rust. Cold Rolled C1010 has a higher carbon content that C1008 resulting in slightly harder material.